Dec 7, 2010 - Internal Error: GEDIT3 - AutoCAD LT 2002 - Program shuts down! System did you also download and install Service Pack 1 by any chance?

Hello ChristopherTaiwo, It looks like AutoCAD 2002 is not compatible with Windows 7. Refer the link for more information. I would suggest you to install AutoCAD in compatibility mode and then check if this fixes the issue. Follow the steps mentioned below to install in compatibility mode: a. Right click on the setup file of the AutoCAD, click Properties, click Compatibility tab, under compatibility mode, make a check mark next to “Run this program in compatibility mode for:” and select “Windows Vista (Service Pack 1 or 2) or Windows XP (Service Pact 2 or 3)” from the drop down list. Click Apply and then click ok.

Under “Privilege level” click “Run this program as an administrator”, click apply and then click ok. Install the AutoCAD successfully and restart the computer for the changes to take effect. Launch the software and check for its functionality. Fajl licenzii k tirika magazin. Also I would suggest you to view the following articles for more information about compatibility mode.

• Obtain your copy of the Longbow Converter • Using Windows Explorer, copy your entire AutoCAD LT 2002 CD to your hard drive, to a folder path c: Autodesk CDs acadlt2002 • Start the Longbow Converter tool • Select the 2nd tab “ Old AutoCAD Installer Reviver“ • Using the ‘’ button, pick the c: Autodesk CDs acadlt2002folder where you just copied the LT 2002 CD • Click the “ Run Old Installer” button. Kv transiver na ms3362 youtube. • Read and understand all the prompts before pressing OK. • Once the setup starts, stop and read the next step • In the setup program, navigate through each setup dialog as normal, except when you get to the installation folder, ** it’s vitally important to make sure you install to c: acadlt2002 (not Program Files (x86) AutoCAD LT 2002 as usually prompted by default)** e.g. You must change the default AutoCAD LT 2002 Install path to c: acadlt2002 • IMPORTANT NOTE: You may find that entering the path C: acadlt2002 may not take (a bug in the AutoCAD 2002 installer). In that case, you will need to select the installation folder C: Program Files (x86) AutoCAD LT 2002 in step (5) below • Do not reboot if prompted to do so • Once installed • Go back to the Converter tool • Select the 3rd tab “ Old AutoCAD Program Reviver“ • Pick the newly installed c: acadlt2002 folder • Click “ Fix Old Program“.

• Now run your AutoCAD LT 2002 and completely register as normal. Once registered, exit AutoCAD and continue to the next step. • Next, unzip and save to c: Autodesk sp – do not install yet • Next, ( ) and save to c: Autodesk sp – do not install yet • Go back into the Converter, select the 3rd tab, select the c: Autodesk sp folder and click Fix. • Install the LT 2002 sp1 by running c: Autodesk sp acad2002LTsp1.exe • If you get a 114 error, you may already have an sp1 enabled product so try the next step • Install the LT 2002 sp2 by running either the unlocked c: Autodesk sp acltk044-k047unl.exe or the locked c: Autodesk sp acltk044-k047swl.exe • If you get a 114 error, read the Troubleshooting section below. • Now, if you can’t get the sp2 to install it’s most likely because your version of AutoCAD 2002 LT is either the locked version and you downloaded the unlocked sp2 or it’s an unlocked version and you downloaded the locked sp2 – go back to (7) and try again. • Now, you can happily run your AutoCAD LT 2002 on Windows 10, Windows 7 and Windows 8. I was able to download the AutoCAD LT 2002 SP1 as described in step 6 above.